Challenger EV1020BMC Inground Car Lift 10,000 lb
Please EMAIL for updated pricing and lead times. Online ordering is disabled at this time due to inventory shortages and manufacturer price increases.
Please note extended lead times for most 2 post and 4 post Challenger lifts. Call for updated status.
CHALLENGER LIFTS EV1020-QC 10,000 LBS CAPACITY INGROUND CAR LIFTS w/ BENCH MOUNT POWER CONTROLS
Inground car lifts with superior arm sweep, the widest drive-thru in the industry plus more service bays (smaller footprint than surface car lifts) means even more revenue. EV1020 EnviroLift™ cassette-style inground lifts meet all the demands of a professional service facility.
With over 50% more bearing contact surface than competitor’s lifts, enhanced wipers both top and bottom and NEW larger 8-1/2” chrome pistons, your shop will have a superior, more stable and repeatable car lift resulting in increased productivity.
FEATURES:
This inground car lift will both optimize space and increase productivity in your repair shop. The EV1020 lift includes enhanced top and bottom wipers, double telescoping screw pads, and 3-stage arms. For an inground car lift that provides 50% more bearing contact surface than competitors, turn to the EV1020 lift.
- Offset 3-stage front and rear arms safely lift both symmetrically and asymmetrically within the same service bay maximizes service capabilities and revenue potential.
- Stainless steel air lock release cylinder prevents car lift from rust associated with condensation
- 87" drive-thru 87" drive-thru provides more tire clearance than competitor's car lifts for wide wheelbase vehicles allowing easy drive-on application.
- Fully contained and sealed polymer cassette tube minimizes risk of hydraulic fluid seeping into the ground as associated with low pressure inground car lifts.
- Double Telescoping Screw Pads minimizes the need for truck adapters by meeting a wider range of vehicle manufacturer designated pick up points.
- NEW Chrome non-breathing ram style cylinder minimizes water intake and other contamination
- 50% more bearing contact than competitors' car lifts provides increased stability.
- NEW Larger 8-1/2" diameter chrome pistons provides car lift with greater stability under load
- Mechanical lock Mechanical lock engages every 3" allowing technician to work at an ergonomic height to increase productivity and minimize fatigue.
- NEW Enhanced raised wiper at top and bottom of bearing provides better grease retention and minimizes contamination from entering into bearings
Details
SPECIFICATIONS
The EV1020 inground car lift is the ultimate lift for upping productivity and meeting the demands of a service facility. It features new 8-1/2” chrome pistons, the widest drive-thru in the industry, and enhanced top and bottom wipers. To find out more about this inground car lift, read the specifications below and determine if this ecofriendly lift is right for your repair shop.
Model Number
| EV1020 |
---|---|
Car Lift Capacity |
10,000 lbs. (4536kg)
|
Stroke |
68" (1727mm)
|
A Rise Height1
|
74" (1880mm)
|
B Width Overall
|
110" (2794mm)
|
C Drive-Thru Clearance
|
87" (2210mm)
|
D Reach (Arm Minimum)
|
19-5/8"
(498mm) |
E Reach (Arm Maximum)
|
42-1/8" (1070mm)
|
F Rubber Pad Adapter (Minimum)2
|
3-7/8"
(89mm) |
G Rubber Pad Adapter (Maximum)2
|
3-7/8" - 6"(98mm - 152mm)
|
Capacity (Per Arm)
|
2500 lbs. (1134kg)
|
Guide Plunger Diameter
|
8 1/2" (216mm)
|
Motor
|
2HP
|
Voltage (Single Phase Std.)3
|
208v-230v
|
Speed of Rise
|
40 seconds
|
Air Required
|
75-125 psi
|
Ceiling Height Required for EV1020 car lifts
|
79" (2007mm)
plus height of tallest vehicle |
Shipping Weight
|
2950 lbs (1338 kg)
|
1 Car Lift Rise Height is measured with superstructure in highest position.
2 Specifications are listed without rubber pad, for measurements with rubber pad add 1-4" (6mm).
3 Optional 3 phase electrical also available. Specify at time of order.
Optional frame engaging adapters (10314 or 10318) are REQUIRED when lifting vehicles with frame construction.