Challenger SA10 Symmetric/Asymmetric Clearfloor Two Post Vehicle Lift 10,000 lb
Please EMAIL for updated pricing and lead times. Online ordering is disabled at this time due to inventory shortages and manufacturer price increases.
Please note extended lead times for most 2 post and 4 post Challenger lifts. Call for updated status.
Challenger Lifts SA10 Symmetric/Asymmetric 10,000 Lbs Two Post Car Lift
Challenger Lifts’ SA10 features the ability to be configured in either the symmetric or asymmetric position dependant upon the service requirements of your shop. The SA10 features 3-stage front arms that provide maximum extension and retraction ensuring safe and reliable lifting on all vehicles within rated capacity.
With adjustable height and width options, double telescoping screw pads, durable powder coat finish, plated arm restraints and pins and many other appealing features, the SA10 will accommodate the rigorous demands of a full service facility. Available in red and blue please choose above.
Our two post lifts come with accessories to turn your two post vehicle lift into a complete productivity center. All Challenger two post lifts are designed and manufactured to the highest standards for performance, durability and longevity.
FEATURES:
- 3-stage front arms provide greater overall arm sweep.
- Padded overhead shut off system prevents vehicle damage from being raised too high.
- Double Telescoping Screw Pads adjust to multiple heights minimizing the need for adapters.
- Premium powder coat finish provides long lasting durable finish.
- Adjustable heights between 11´ 4-1/4" and 11´ 10-1/2" and adjustable widths 10´ 9" to 11´ 5-1/2" provides versatility at installation for service facilities with spacial constraints.
- Rubber door guards provide added security against vehicle door damage.
- Single-point mechangical lock release system allows technician to disengage both columns simultaneously.
- Mirrored "S" shaped columns provides a clear and sage concave conduit for the bearings.
Details
SPECIFICATIONS:
Â
Model Number
| SA10 | |
---|---|---|
Lift Configuration |
Symmetric Configuration
|
Asymmetric Configuration
|
Lift Capacity* |
10,000 lbs. (4536kg)
|
|
AÂ Rise Height1
|
74-1/2" (1892mm)
|
|
BÂ Overall Height
|
11' 4-1/2" / 11' 10-1/2" (3467mm / 3620mm)
|
|
CÂ Overall Height (Cylinder Extended)
|
11' 10-1/2" (3620mm)
|
|
DÂ Overall Base Width
|
10' 9" / 11' 3" (2356mm / 2508mm)
|
10' 11-1/2" / 11' 5-1/2" (3340mm / 3493mm)
|
EÂ Drive-Thru Clearance
|
92-3/4" / 98-3/4" (2356mm / 2508mm)
|
88-1/2" / 94-1/2" (2248mm / 2426mm)
|
FÂ Floor to Overhead Swith
|
131-1/8" / 137-1/8" (3331mm / 2483mm)
|
|
GÂ Short Arm Reach
|
22-3/8" - 41-1/2" (3331mm - 1054mm)
|
|
HÂ Long Arm Reach2Â (min/max)
|
38-1/4" - 59" (972mm - 1499mm)
|
|
IÂ Screw Pad Height
|
4-3/8" - 6-1/2" (111mm - 165mm)
|
|
JÂ Inside of Columns
|
106-3/4" / 112-3/4" (2711mm - 2864mm)
|
101-1/2" / 107-1/2" (2578mm - 2731mm)
|
Motor
|
2HP, Single Phase, 60Hz
|
|
Voltage
|
208v - 230v
|
|
Speed of Rise
|
48 seconds
|
|
Max. Load per Arm
|
2,500 lbs. (1134kg)
|
|
Ceiling Height Required
|
12 (3658mm)
|
*Lift capacity ratings are based on loads equally distributed on all four arms.Â
1 Rise Height is measured with telescoping screw pads in highest position.Â
2 Specifications are listed without rubber pad, for measurements with rubber pad add 1/4" (6mm)Â
3 Overall width of Asymmetric lift is 11' 3"' / 11' 9" including power unit
*Frame engaging adapters (10314 or 10318) are REQUIRED when lifting vehicles with frame construction*