Challenger CL10V3-2-DPC Versymmetric® Plus, Dual Pendant Controls, 2' Column Extension, Two Post Vehicle Lift 10,000 lb
Please EMAIL for updated pricing and lead times. Online ordering is disabled at this time due to inventory shortages and manufacturer price increases.
Please note extended lead times for most 2 post and 4 post Challenger lifts. Call for updated status.
Challenger Lifts CL10V3-2-DPC Versymmetric 10,000 Lbs Two Post Lift W/ 2' Extensions And Dual Pendant Controls
CL10 SERIES
CL10series Versymmetric® 2-Post Lifts feature a 2 Lifts in One Design to that provides the flexibility to lift vehicles asymmetrically or symmetrically within the same service bay. Other standard features include space saving column base plates with clear floor design, overhead cable equalization system, timesaving single-point or dual single-point mechanical lock release system, padded overhead shutoff bar and round double telescoping screw pads.
DESCRIPTION:
Challenger Lifts CL10V3-2-DPC Two Post Car Lift Versymmetric Plus 2-post lift w/ Dual Pendant Power Controls, offset 3-stage front + 3-stage rear arms & dual single-point mechanical lock release. Includes Stack Adaptor Kit (Part#10315), Document Caddy (Part #10320) and Pendant Holder (Part #10321), (13' 8" ht. at full stroke) (Single phase only)
Dual Pendant Power Control (DPC)
Expedites vehicle spotting by providing an unobstructed view to lifting points
Up/Down power button + dual singlepoint technical lock release system provides lift operation from either column
OSHA compliant keyed lockout safety button
Details
FEATURES:
- Max Plus Productivity (CL10V3DPC) - Dual Pendant Power Controls, Stack Adapter Kit and Document Caddy with Versymmetric® Plus offset 3-stage front + 3-stage rear arms
- 13´ 8” standard height allows lift to be placed in standard service bay with 13´ 9" ceiling
- Adjustable arm restraint shafts compensate for uneven floors
- Grease fittings located on arm pin bushings minimize corrosion to keep arms swinging freely
- Available 2´ and 3´ column extensions enable technician to work at an ergonomic height when servicing taller vehicles
- Double Telescoping Screw Pads adjust to multiple heights minimizing the need for adapters
- 48” elongated carriage design decreases load on bearing
- Heavy-Duty 5 diameter pulley and 5/16 cable reduces stress on equalization system and increases cable life
- Padded overhead shut off system prevents vehicle damage
- Single-point mechanical lock release system allows technician to disengage both column locks simultaneously
- Rubber door guards protect vehicles from door damage
- Made in USA
SPECIFICATIONS:
- Lift Capacity: 10,000 lbs. (4535kg)
- A Rise Height: 74-1/8" (1908mm)
- B Column Height: 13´8" (4166mm)
- C Cylinder Overall (Full Stroke) 11´11" (3632mm)
- D Adjustable Width Overall: 11´6-1/2" / 105" (3518mm / 3632mm)
- E Drive-Thru Clearance: 100-1/2" / 105" (2553mm / 2667mm)
- F Floor to Overhead Switch: 13´2-1/2" (4026mm)
- G Front Arm Reach (Min/Max) Min. 19-13/16" / Max.42" (956mm/1524mm)
- H Rear Arm Reach (Min/Max) Min. 37-5/8" / Max. 60" (956mm / 1524mm)
- I Screw Pad Height: Min. 3-7/8" / Max. 6-1/2" (98mm / 161mm)
- J Inside Columns: 110" / 114-1/2" (2794mm / 2908mm)
- K Low Lock Height: 12" (305mm)
- Motor: 2HP
- Voltage: 208v-230v (Single Phase Standard)
- Speed of Rise: 48 seconds
- Max. Load per Arm: 2,500 lbs. (1134kg)
- Ceiling Height Required: 13´9" (4191mm)
*Lift capacity ratings are based on loads equally distributed on all four arms. 1 Rise Height is measured with adjustable screw pads in highest position. 2 Specifications are listed with lift at maximum width and/or height settings. 3 Specifications are listed without rubber pad, for measurements with rubber pad add 1/4" (6mm). 4 Optional 3 phase electrical also available (Not available for Quick Cycle models). Specify at time of order. Standard lift colors are Red and Blue. Optional colors available.
Optional frame engaging adapters (10314 or 10318) are REQUIRED when lifting vehicles with frame construction.
Reviews
Best Selling Products
